Update instructions for the MMI High update MMI update programming for vehicles equipped with MMI High, e.g. A8 (4E), A6 (4F), Q7 (4L), A5 (8T), and A4 (8K) via the on-board CD drive with feedback documentation via Software Versions Management (Audi SVM): Update instructions for the MMI High update MMI update programming for vehicles equipped with MMI High, e.g. A8 (4E), A6 (4F), Q7 (4L), A5 (8T), and A4 (8K) via the on-board CD drive with feedback documentation via Software Versions Management (Audi SVM) The steps which have to be carried out are explained in the Business TV episode 191/2002.

I seem to have aquired a copy of the Audi_MMI_5570_3cd_set_4L0.998.961 which according to other forums seems to have worked to update the software - the weird thing is they all seem to have a SW version for all sorts (like bluetooth, amp, B&O etc) whereas I just have a single software version as show. Kak sdelatj ulej iz penopolistirola svoimi rukami video.

See the film in a format which can be played on a Windows Media Player on the update CD 420906961B. Also see the iTV programme 2345 about Online flashing and SVM. The iTV programme is on the following update CDs: CD 8D0906961C, 8Z0906961B, and also 8N0906961A.

Contents 1.Overview of controls.......3 2.Important information about update programming....4 3.Carryingoutupdateprogramming.....6 4.Changing the language of the MMI speech dialogue system (SDS)..12 5.USB – consumer update for the Audi music interface (AMI)...18 6.SVM feedback documentation......19 7.Table of figures.......28 1. Overview of controls Figure 1: Controls (depending on vehicle type) ␣ ON/OFF button with volume control ␣ Rotary pushbutton ␣ RETURN button ␣ Function selector buttons ␣ Control buttons ␣ Arrow buttons ␣ Fingerprint (not used in these instructions) 2. Important information about update programming Attention: ␣ ␣ (Failure to observe these instructions can cause hardware faults!) ␣ Do not leave the flash CD in the vehicle!

Check that your software meets the requirements for update programming. Requirements: 1 MMI flash CD (get the part number from the relevant TPL episode or step instructions). Check that the no-load voltage of the vehicle battery is at least 12,5V. Let the engine run for 1 minute and then immediately continue with update according to the instructions. Connect a battery charger (VAS5095) to maintain vehicle voltage through out the entire update programming session. Switch off all equipment with high electromagnetic emission values (such as mobile telephones or cordless land-line telephones) in and around the vehicle.

The Bluetooth handset (included with factory-installed Bluetooth car phone BTA) must be switched on. Diagnostics using the VAS tester must not be run in parallel. The ignition can be switched off and remain off.

8.Switch off all unnecessary electrical equipment (daytime running lights, air conditioning, etc.) in the vehicle and leave it switched off until all update programming has been completed. EnsurethatnootherCDs(audioCDs,electronicon-boardhandbook,etc.)areinthe CD drives while running update programming.

It is essential that you adhere to the flash sequence! After each update, the MMI system must be restarted and checked if there are still control units that need updating. This is necessary because some control units can only be updated in the second step. Note: The screen shots in these instructions are for your information only, i.e. The texts shown here are not necessarily identical to the texts you will see on your display. If problems should occur during the MMI software update, you can find important information about possible sources of error in the Audi Servicenet under 'Technology – Product support – Electrical – Multi Media Interface (MMI) – MMI High'. Carrying out update programming 1.

Switch on MMI. Remove all CDs from the CD changer/CDplayer. 3.Put the MMI update CD into the first slot of the CD changer or the CD drive with the label facing up. Wait at least 2 minutes to allow the system to analyze the MMI update CD and for the MMI System to be ready to be updated. Activate the RADIO menu by pressing the corresponding function selector button. First press SETUP and then RETURN and hold both buttons down simultaneously for about 5 seconds until the display changes.

Activate the SW update by pressing the bottom right control button. Figure 2: Selecting the SW update using the bottom right control button 8. Activate the update from the CD-ROM by pressing the rotary push button. Figure 3: Selecting update of CD-ROM by pressing the rotary pushbutton 9. Wait at least 20 seconds while the Meta information is being read. Figure 4: Waiting while the Meta information is being read 10.Select and activate 'Standard' using the rotary pushbutton. Figure 5: Selecting 'Standard' using the rotary pushbutton 11.The list which now appears shows all the devices which can be updated.

Figure 6: List view of the devices to be updated Type of change: N/A= No update information available on the present CD N= No update required E= Single update (partial update: bootloader or application) will be performed J= Bootloader and application will be changed (complete update) 12.Using the rotary pushbutton, select and confirm ”Start download” at the end of the list. Figure 7: Activating Start download using the rotary pushbutton 13.Read the note if one appears. Then select and activate 'OK' at the end of the list using the rotary pushbutton (this only appears in the case of a bootloader update of a component). Figure 8: Start download by selecting 'OK' using the rotary pushbutton Note: A warning message may appear informing you about the risk of damaging control units. You can ignore this message at this point.